si si tengo un disco duro scsi.... y no encuentro en donde esta montado haber si me puedes hechar la mano para saber este es el resultado ke arroja ese comando... la usb es marca Victorinox
Vendor: _NEC Model: CD-RW NR-9300A Rev: 105B
Type: CD-ROM ANSI SCSI revision: 02
IA-32 Microcode Update Driver: v1.13 <
[email protected]>
microcode: No suitable data for cpu 0
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
Attached scsi CD-ROM sr0 at scsi2, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
inserting floppy driver for 2.4.21-27.0.2.EL
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Intel(R) PRO/1000 Network Driver - version 5.3.19-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
PCI: Found IRQ 9 for device 01:0c.0
PCI: Sharing IRQ 9 with 00:1d.2
PCI: Sharing IRQ 9 with 00:1f.1
PCI: Sharing IRQ 9 with 00:1f.2
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
divert: allocating divert_blk for eth0
divert: freeing divert_blk for eth0
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (4027 buckets, 32216 max) - 304 bytes per conntrack
Intel(R) PRO/1000 Network Driver - version 5.3.19-k2-NAPI
Copyright (c) 1999-2004 Intel Corporation.
PCI: Found IRQ 9 for device 01:0c.0
PCI: Sharing IRQ 9 with 00:1d.2
PCI: Sharing IRQ 9 with 00:1f.1
PCI: Sharing IRQ 9 with 00:1f.2
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
divert: allocating divert_blk for eth0
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
audit subsystem ver 0.1 initialized
Audit daemon registered (process 2885)
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 431M
agpgart: Detected an Intel(R) 865G Chipset.
agpgart: Detected 8060K stolen memory.
agpgart: AGP aperture is 128M @ 0xe8000000
memory : dcb92680
memory : dcb92700
memory : dcb92780
[drm] AGP 0.99 Aperture @ 0xe8000000 128MB
[drm] Initialized i830 1.3.2 20021108 on minor 0
mtrr: base(0xe8020000) is not aligned on a size(0x300000) boundary
memory : dcb92880
memory : dcb92900
memory : dcb92980
memory : dcb92a00
memory : dcb92a80
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:1d.0
PCI: Sharing IRQ 11 with 00:1d.3
Intel 810 + AC97 Audio, version 1.01, 23:54:16 Jan 12 2005
PCI: Found IRQ 3 for device 00:1f.5
PCI: Sharing IRQ 3 with 00:1f.3
PCI: Setting latency timer of device 00:1f.5 to 64
i810: Intel ICH5 found at IO 0xedc0 and 0xee00, MEM 0xfeb7fa00 and 0xfeb7f900, IRQ 3
i810: Intel ICH5 mmio at 0xe08a9a00 and 0xe08ab900
i810_audio: Primary codec has ID 0
i810_audio: Audio Controller supports 6 channels.
i810_audio: Defaulting to base 2 channel mode.
i810_audio: Resetting connection 0
i810_audio: Connection 0 with codec id 0
ac97_codec: AC97 Audio codec, id: ADS116 (Unknown)
i810_audio: AC'97 codec 0 supports AMAP, total channels = 2
hub.c: new USB device 00:1d.2-2, assigned address 2
usb.c: USB device 2 (vend/prod 0x1370/0x6828) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi3 : SCSI emulation for USB Mass Storage devices
Vendor: SWISSBIT Model: Victorinox Rev: 1.89
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdb at scsi3, channel 0, id 0, lun 0
SCSI device sdb: 5120 512-byte hdwr sectors (3 MB)
sdb: Write Protect is on
sdb: sdb1
sdb2 sdb3 sdb4
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
udf: registering filesystem
UDF-fs DEBUG lowlevel.c:57:udf_get_last_session: XA disk: no, vol_desc_start=0
UDF-fs DEBUG super.c:1421:udf_read_super: Multi-session=0
UDF-fs DEBUG super.c:410:udf_vrs: Starting at sector 16 (2048 byte sectors)
UDF-fs DEBUG super.c:437:udf_vrs: ISO9660 Primary Volume Descriptor found
UDF-fs DEBUG super.c:440:udf_vrs: ISO9660 Supplementary Volume Descriptor found
UDF-fs DEBUG super.c:446:udf_vrs: ISO9660 Volume Descriptor Set Terminator found
UDF-fs DEBUG super.c:1430:udf_read_super: UDF-fs: No VRS found
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A